Engine is continued from previous page.
See our complete selection
Steering System Accessories
Protect your cables and hoses with
this easy to remove rigging sleeve.
Made of rugged, UV- and weather-
sleeve will withstand the elements
and resist fading. Easily zips on
and off to access cables or hoses
when needed. Ends are secured
with cable ties sewn into pockets.
with Fuel Hose Port &
Rigging Hose Union
Complete your professional rigging installation with these
two Rigging Flanges. They rig cables and electrical with fuel
primer bulb exposed. Split design allows installation on pre-
rigged boats. Installs with T-H Marine Rigging Hose. Fuel
hose port fits Type A hose, and Hose Union fits Type B hose.
Complies with NMMA and ABYC requirements.
Strain Relief Kits
Prevents kinks and chafing in hydraulic
steering hose, distributing strain from bends in the hose and sealing out water
with a watertight gripper fitting. Bulkhead fitting has 2 3/4" diameter flange for
protection. Requires 1 1/4" installation hole. Note: only bulk hose can pass
through this fitting. Pre-made hoses with end fittings cannot pass through.
Intended to protect the system's components and assist
in purging air.
TELEF # ShWt
Power Steering Oil Reservoir
Simplifies maintenance and assists the in-line cooler
on all SeaStar power steering systems. Rubber-
mounted aluminum bracket provides resistance to
vibration and easy access to top-mounted fill port.
Front-facing air pressure gauge and easily viewed
minimum/maximum sight lines for system pressure
and fluid level maintenance. An extra 1/4" NPT
port is supplied should it be needed for auxiliary
equipment or hose routing considerations. 10 1/4"H
x 5 1/4"dia. (exclusive of lower fittings and gauge).
TELEF# HP5810HY ShWt 5.6
SeaStar Hydraulic Steering
Reservoir with Relief Valve
Combines the function of a hydraulic fluid reservoir with pressure gauge and
a relief valve into a single component. Reservoir: 6" dia., 950psi relief, 1qt.
capacity. Overall unit height (including pump and gauge): 9 1/4". Spacing
between brackets: 4 7/8".
TELEF# HP5860HY ShWt 6.8
SeaStar Steering Accessories
Hydraulic Steering Fluid
Ensures the best steering system operation. Meets
Mil Spec H5606C.
TELEF # HA5430 ShWt 2
Flexible 3/8"OD, 5/16"ID nylon tubing for use on
all SeaStar I and II helm installations. Maximum
recommended length is 100'. Sold by the foot.
TELEF # HT5100 ShWt .1
Flexible hose screws onto bottle of steering fluid and
to the helm for quick and easy filling.
TELEF # HA5438 ShWt .1
Used to retrofit the SeaStar 3" helm into 4 1/2" dash
cutouts. Can also reduce the helm's protrusion by a
width equal to the thickness of the dash.
TELEF # HA5418 ShWt .2
Dual Station Fitting Kit
For I/Os and inboards. Contains fittings for adding
a second steering station or an autopilot system to
an existing SeaStar sterndrive or inboard steering
system. Allows use of SeaStar hose. Includes non-
vented fill plug for helm at uppermost station.
TELEF # HF5502 ShWt .5
20 Dash Wedge Kit
Allows a SeaStar helm to be mounted 20 from
perpendicular in any of four configurations (not
TELEF # HA5419 ShWt 2
Sternflex Rigging Hose
Shields Sternflex has a polyethylene
copolymer wall with an integral polyethylene
helix. It is resistant to abrasion, crushing and
UV. This hose is primarily used as a cover for the harness and for the hoses on
bracket-mounted outboard engines. 2" (50.8mm) ID. Black. Sold by the foot; 50'
max continuous length.
SHIEL# 116-126-2000B ShWt .3
Rigging Hose Kit
This kit hides all engine cables and
hoses, and can be added to any style
outboard. Contains UV-stabilized flange
and 5'2" black sternflex hose.
With a large opening to pass bundled wires through,
these rugged vinyl boots won't need to be cut or slit.
To complete the installation, snug up the supplied
THMAR # ShWt
Rigging Flange with Fuel Hose Port
Rigging Flange Hose Union
THMAR # ShWt
Bulkhead Strain Relief Kit with Chrome Base
Bulkhead Strain Relief Kit with Black Base
Previous Page - Next Page
-2015-2016 Master Catalog
Choose a different catalog.